eye CLEAN
OIL FILTRATION
Up to 5x longer use of oil due to patented filter system
This filtration of oil configuration is ready to be used on site
-
Offline oil filtering using micronic high efficiency filters
-
Changeable filter for a filtration of 16 l per minute
-
Recommended oil temperature: 10 to 85 °C
-
Three different micron filters: 10 µm, 5 µm, 3 µm
-
Three different elements for spin-on filters: 10 µm, 5 µm, 3 µm
-
Oil life up to 5x longer than normal
-
Filtration of saturated water
-
Filtration of oxidized oil
Assuming your oil can be used up to 5x longer than before, what would that mean for you?
Sample cost calculation
- Mineral oil cost: 5 € / l
- Synthetic oil cost: 9 € / l
- Large gearbox oil capacity: 800 l
- Medium gearbox oil capacity: 500 l
Filtering with eye CLEAN
- Costs: Investment in eye CLEAN + 100 € filter sets
Costs not taken into account that arise during normal oil replacement
- Down time to change the oil
- Operations for the oil change
- Recycling cost of the dirty oil
Working Principle
Basic Principle
A electric motor
B oil pump
C filter
The electric motor (A) supplies electrical power to the oil pump (B). The oil pump moves the oil through the filters (C) to remove contamination particles and water.
Depth filter
The depth filter removes water and varnish (sludge) from the oil.
The depth filter also removes particles from the oil:
A The top of the filter removes the biggest solid particles
B The middle of the filter removes solid particles of moderate size
C The bottom of the filter removes the smallest solid particles
Suction filter
The suction filter removes the largest particles from the oil.
The suction filter has an internal bypass to prevent a failure of the pump. The oil continues to go through the pump when the suction filter is saturated.
Pressure filter
The pressure filter removes small particles from the oil.
The pressure filter han an internal bypass to make sure that a heater or a cooler is supplied with oil when the pressure filter is saturated.
Filling
A Container
B Device
C Gear unit or hydraulic system
Oil from a container (A) goes through the device (B) to a gear unit or a hydraulic system (C).
Draining
A Gear unit or hydraulic system
B Device
C Container
Oil from a gear unit or a hydraulic system (A) goes through the device (B) to a container (C).
The device removes oil from the gear unit or the hydraulic system. The container temporarily holds the oil.
Transfer
A Container
B Device
C Container
Oil from a container (A) goes through the device (B) to a different container (C).
Use transfer, for example:
- To move contaminated oil to a waste container.
- To move oil from one container to a different container
- To clean contaminated oil from a container
Bypass
Permanent filter
A Gear unit or hydraulic system
B Device
The device operates as a permanent filter in bypass. Oil from a gear unit or a hydraulic system (A) goes through the device (B) and back to the gear unit or the hydraulic system.
Filter for big or heavily contaminated systems
A Gear unit or hydraulic system
B Device
C External filter housing with high capacity
The device operates as a bypass system. For big and heavily contaminated systems, an external high capacity filter can be added in the pressure line. The device does not control the external filter.
Oil from a gear unit or a hydraulic system (A) goes through the device (B) and the external filter (C) and back to the gear unit or the hydraulic system.
Filter with cooler and/or heater
A Gear unit or hydraulic system
B Heater
C Device
D Cooler
The device operates as a bypass system. To cool or heat the oil, external cooling or heating equipment can be added in the oil lines. The device does not control the cooling or heating equipment.
Cooler
Hot oil from a gear unit or a hydraulic system (A) goes trhough the cooler (D) when the oil goes back to the gear unit or the hydraulic system. The cooler decreases the temperature of the oil.
Heater
Cold oil from a gear unit or a hydraulic system (A) goes through the heater (B) when the oil goes through the device (C). The heater increases the temperature of the oil which makes it easier for the device to clean the oil.
Spare parts and accessories
- 3/4 inch
- 1 inch
- 1 1/2 inch
- 2 inch
- 5 µm
- 10 µm
- 5 µm
- 10 µm
- 125 µm (Protection filter)